Steam Generator B.E Question Paper : jaduniv.edu.in
Name of the University : Jadavpur University
Department : Power Engineering
Degree : B.E
Subject Name : Steam Generator
Year/Sem : III/II
Website : jaduniv.edu.in
Document Type : Model Question Paper
Download Model/Sample Question Paper : https://www.pdfquestion.in/uploads/ds…0Generator.pdf
Steam Generator Question Paper :
Bachelor Of Power Engg. Examination, 2011 :
(3rd Year, 2nd Semester, Supplementary)
Time : Three hours
Full Marks : 100
Use separate Answer-Script for each part.
Related : Jadavpur University Electrical Machine & Power Control B.E Question Paper : www.pdfquestion.in/6148.html
PART – I : (50 marks)
Answer any three questions :
Two marks for neatness. :
1. a) What is fine tube boiler? 3
b) Describe features of a five tube boiler. 8
c) What are the limitations of a fire tube boiler? 5
2. a) What are boiler mountings? Why are they provided? 6
b) Describe four major mountings of a modern boiler. 10
3. a) What is fluidigastion? 4
b) State imfortant properties of a fluidized led. 4
c) Describe imfortant features of a bubbling led boiler. 8
4. a) Why is draft system provided for boiler? 2
b) What are different draft systems? 6
c) Describe functions of climney. 4
d) Explain how chimney height is established. 4
5. Write few lines on : 4×4
a) Function of ignitor.
b) Straight flow coal burner.
c) Dumping grate stokes.
d) Direct coal fining system of boiler.
PART – II : (50 marks)
Answer any three questions :
Two marks for neatness and to the answer. :
6. a) How does a tower type boiler layout from a p -type layout? In which type of boilers the former layout is preferred? 3+1
b) In a p -type steam generator layout of a utility power station show the different tube arrangements and mark the working fluid flow path. 10
c) How do you classify a steam generator based on (i) tube content and (ii) draft? 2
7. a) In a finned economizer, on which side of the tube wall would you recommend to put the fin and why? Discuss with sketch the most suitable fin arrangement on the wall of an economizer tube bank. 4+4
b) Feedwater enters the economizer of a power station steam generator at 180 bar 2500C and with a flow rate of 1500 T/h. The flue gas flow rate is 2200 T/h and the temperatures of the flue gas entering and leaving the economizer coil are 5300C and 3600C, respectively. The overall heat transfer coefficient based on the inside area of the economizer tube is 70 W/m2 K. If the velocity of water entering the economizer is 1 m/s and the internal diameter of the tube is 50 mm, find out the number of coils in the economizer and the length of one coil. Take specific heat of flue gas as 1.1 kJ/kg0C. 8
8. Differentiate between : 4×4
i) Nucleate boiling and film boiling in pool boiling
ii) Annular flow and mist flow in forced flow boiling
iii) Dry out and burn out of evaporator tube.
iv) Void fraction and volumetric quality in two phase flow.
9. a) Define circulation ratio. How is it related to the dryness fraction at the riser exit? 2+1
b) How does circulation take place in a natural circulation boiler? What do you mean by assised circulation? 3+2
c) Discuss with a neat sketch the internal arrangements of a steam drum in a power station steam generator. 8
10. a) What is refractory coated water wall and when is it used? 4
b) Why is it necessary to control the steam temperature at superheater outlet? State the effects of the variation in the following steam generator operating variables on the superheater outlet steam temperature : (i) Load, (ii) feed water inlet temperature. 4+4
c) How does the attemperator control the superheated steam temperature? 4
11. a) What are the advantages of preheating air in a steam generator? What are the advantages and limitations of regenerative air preheater over the recuperative type? 2+4
b) What do you mean by cold end corrosion? How can it be avoided in a steam generator? 4
c) What are the major losses that occur in a steam generator? How does the boiler loss depend on the supply of air to the boiler? 2+4