07A70309 Robotics B.Tech Question Paper : scce.ac.in
Name of the College : SREE CHAITANYA COLLEGE OF ENGINEERING
University : JNTUH
Department : Mechanical Engineering
Subject Code/Name : 07A70309/ROBOTICS
Year/Sem : IV/I
Website : scce.ac.in
Document Type : Model Question Paper
Download Model/Sample Question Paper : https://www.pdfquestion.in/uploads/scce.ac.in/4911-07A70309-ROBOTICS.pdf
Robotics Question Paper :
Code No: 07A70309
R07 Set No. 2
IV B.Tech I Semester Examinations,December 2011
Related : Sree Chaitanya College Of Engineering 07A70308 Power Plant Engineering B.Tech Question Paper : www.pdfquestion.in/4912.html
Common to Mechanical Engineering, Mechatronics
Time: 3 hours
Max Marks: 80
Answer any FIVE Questions :
All Questions carry equal marks :
1. (a) What are the general considerations in selecting a robot for material handling?
(b) Discuss the robot application in pick – and – place operations. [8+8]
2. (a) Explain the principle of working of potentiometer.
(b) At time t, the excitation voltage to a resolver is 24 V and the voltage across the two pairs of stator terminals will be 12 p 3 V and 12 V. What is the shaft angle? [8+8]
3. Write an explain the algorithm for deriving the forward kinematics for any manipulator based on D-H convention. [16]
4. Draw and explain with an example the Composite rotations algorithm. [16]
5. Discuss suitable design of robot end-eectors to grip objects like
(a) Shafts
(b) Rings
(c) Flanges. [16]
6. (a) What are the important items to be considered in deciding the use of robots in
i. Manufacturing operation
ii. Hazardous operation.
(b) What is meant by machine intelligence? What is AI? Illustrate a unified model of AI and Robotics. [8+8]
7. Using Norton – Euler forward equations, determine the joint torques or forces of a planar PR robotic Manipulator. [16]
8. (a) Using WAIT, SIGNAL and DELAY commands write a program for the press unloading task.
(b) Using the 8 8 grid of a robot with one rotational axis and one linear axis, show the path taken by the robot if it is directed to move between point ( 2, 2 ) and point ( 7, 5 ) in the grid using joint interpolation. [8+8]
Code No: 07A70309
R07 Set No. 4
1. (a) What are the features of Robots in Arc welding? Explain.
(b) What are the benefits of Robot spray painting? Explain. [8+8]
2. (a) Discuss the SPEED control commands of Robot languages.
(b) Discuss the characteristics of Robot level languages. [8+8]
3. Find the coordinates of point P(2; 3; 4)T relative to the reference frame after a rotation of 450 about the x-axis. [16]
4. (a) Explain the working of AC servo motor.
(b) At time t, the excitation voltage to a resolver is 24 V and the voltage across the two pairs of stator terminals will be 12 V and 12 p 3 V. What is the shaft angle? [8+8]
5. Using Norton – Euler forward recursive equations, determine the motion parameters of the joints and the center of mass of links of a planar PR robotic Manipulator. [16]
6. Sketch any Four of the following robots indicating the joints and degrees of freedom:
(a) Polar robot
(b) Cylindrical robot
(c) Cartesian robot
(d) SCARA robot
(e) Gantry robot
(f) Jointed arm robot. [4+4+4+4]
7. What is remote centre compliance device? What is the lateral error and the angular error involved in inserting a peg in a hole? [4+12]
8. Consider the United States Robots Maker 110 manipulator. This is a five-axis spherical coordinate robot with a pitch-roll spherical wrist. Use the last half of the D-H algorithm to fill in the kinematic parameters for the Maker 110 in the table, consistent with the link-coordinate diagram. Indicate which parameters are the joint variables. [16]
Robotics Set No 1 :
1. Sketch and explain some linkage mechanisms for mechanical grippers. [16]
2. (a) Explain the kinematic equations using homogeneous transformations.
(b) Explain the homogeneous transformations as applicable to rotation. [8+8]
3. (a) Explain the skew motion and joint interpolated motion with path control.
(b) A jointed – arm robot of conguration RRR is to move all three axes so that the rst joint is rotated through 500, the second joint is rotated through 900 and the third joint is rotated through 250.
Maximum speed of any of these rotational joints is 100/s. Ignore eects of acceleration and deceleration.
i. Determine the time required to move each joint if skew motion is used.
ii. Determine the time required to move the arm to the desired position and the rotational velocity of each joint, if joint – interpolation motion is used. [6+10]
4. (a) What is the dierence between standard servo and feed forward servo?
(b) What is error in the control loop and how can it be eliminated?